ADC-V522IR Indoor Camera Guide

Jan 18, 2020
You are here:
Estimated reading time: 2 min


  • 1920 x 1080p video resolution
  • 113° horizontal and vertical field of view
  • 15′ Night Vision range
  • 802.11 b/g/n WiFi
  • Ethernet connection
  • Micro SD Card slot (not functional at this time)
  • 2-way audio
  • Operating Temperature 32°F to 104°F


Factory Default

Warning! Erases everything, camera must be re-added to and WiFi configured

Insert paper clip into reset hole and hold internal button for 15 seconds


WiFi Setup by WPS Mode

1. Insert paper clip into reset hole and hold internal button 5 seconds until LED flashes blue


2. Press and release router WPS button or enable WPS in router programming


3. Camera LED turns green after 1 minute if successful


WiFi Setup by Access Point

1. Insert paper clip into reset hole and hold internal button 6 seconds until LED flashes white

ADC-V522IR_Camera_AP_Access_Point_Mode.jpg ADC-V521IR_White_LED.jpg

2. Go to smartphone WiFi settings, select ALARM xx:xx:xx then press CONNECT

AP_Mode_Setup_01.png AP_Mode_Setup_02.png AP_Mode_Setup_03.png

3. Open web browser and enter, camera menu appears, select language

AP_Mode_Setup_04.png AP_Mode_Setup_05.png AP_Mode_Setup_06.png

4. Press SCAN FOR WI-FI NETWORKS, when found select WiFi network

AP_Mode_Setup_07.png AP_Mode_Setup_08.png AP_Mode_Setup_09.png

5. Select SECURITY KEY then enter WiFi encryption key then press SAVE then OK to exit

AP_Mode_Setup_10.png AP_Mode_Setup_11.png AP_Mode_Setup_12.png

6.  Camera green LED turns ON if successful


Hardwire Connection to Router

Connect Ethernet cable from camera to port on back of router and power up camera


Add Camera using Customer Website

Note: Camera must be connected to customer’s router by WiFi or Ethernet Connection

1. Login to customer website and press VIDEO




3. Scroll to bottom of page and press ADD VIDEO DEVICE


4. Camera should be detected, enter camera name then click on INSTALL to continue


5. downloads information to camera, this may take up to 5 minutes


6. When complete press LIVE VIEW to view camera


7. If connected by Ethernet and needing to configure WiFi press SETTINGS


8. Scroll down to the bottom of the page then press WIRELESS NETWORK


9. Press SCAN to scan for networks


10. Select WiFi network


11. Enter WiFi encryption then press NEXT


12. Power camera down then unplug Ethernet cable then power up and wait 2 minutes


Add Camera using Smartphone App

Note: Camera must be connected to customer’s router by WiFi or Ethernet Connection

1. Press top left Bars to access side menu then select VIDEO then press top right GEAR icon

ADC-V522_Setup_by_App_01.png ADC-V522_Setup_by_App_03.png ADC-V522_Setup_by_App_02.png

2. Press ADD VIDEO DEVICE then press INSTALL then enter camera name then NEXT

ADC-V522_Setup_by_App_04.png ADC-V522_Setup_by_App_05.png ADC-V522_Setup_by_App_06.png

3. Camera may take several minutes to configure, press X at top left to exit

ADC-V522_Setup_by_App_07.png ADC-V522_Setup_by_App_08.png ADC-V522_Setup_by_App_09.png


  • Power cycle the camera by unplugging and plugging in power adapter
  • Move closer to WiFi router
  • If issues persist, try resetting the camera to factory defaults

LED Reference Guide

  • Solid Green = Local network and Internet connection OK
  • Flashing Green = Local network connection OK, Internet connection bad
  • Solid Red = No local network or Internet connection
  • Flashing Red = Camera booting
  • Flashing Blue = Camera in WPS WiFi learn mode
  • Flashing White = Camera in WiFi AP learn mode
  • Flashing Yellow = Camera in Bluetooth Pairing mode
Was this article helpful?
Dislike 0
Views: 79